6530A REV E Norge Washer Parts List

Search the entire 6530A REV E by part description. Keep descriptions simple, e.g. "belt" or "pump". Need help?

Thermal cut-off kit (use wpl 279816)

This thermal cut-off kit for a dryer includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse (309 degrees). The thermal cut-off (fuse) is meant to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when it does trip, you must replace it. The hi-limit thermostat acts as a safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this piece will shut down power to the heating element. This genuine OEM kit also includes flat heaters with jumper wires. Make sure to disconnect the power source to the dryer before beginning this repair.

Easy Part #:
EAP334299
Availability:
In Stock
Price:
$41.40

Rear drawer glide (range storage drawer glide)

This rear drawer glide is for your bottom range drawer. As the broiler drawer slides back and forth, these glides prevent metal-to-metal contact. If you are having trouble opening/closing the broiler drawer, the glide may be broken and will need to be replaced. This is a genuine OEM part and is sold individually.

Easy Part #:
EAP434227
Availability:
In Stock
Price:
$4.93

Halogen light bulb - 120v 20w (bulb halogen (120v 20w))

This clear 20-watt, 120-volt halogen light bulb is a replacement part for the bulb behind the top grill in your microwave. The light bulb is used on the inside of your microwave to provide light when the door is open, or below the microwave to provide light for the cooking area. If the bulb in the microwave is burnt out or broken you will need to replace it. This is a genuine OEM halogen light bulb and is sold individually.

Easy Part #:
EAP2351821
Availability:
In Stock
Price:
$20.61

Tumbler and motor belt (sub 312959)

The drum drive belt is made to wrap around the drum, slip on the tension pulley to rotate the drum. If your dryer drum won’t turn when in operation, the drum drive belt is probably broken and will need to be replaced. This drive belt is 3/8” wide 100” long with 5 ribs and 4 grooves. It is recommended to disconnect the power to your dryer before you start your repair. This drum drive belt is a genuine OEM part.

Easy Part #:
EAP11757542
Availability:
In Stock
Price:
$27.07

Tub dampening strap (strap damping)

This part is used to support the tub and keep it in the center of the cabinet to reduce vibration. If your washer is making loud noises, or shakes or moves, one or more of the straps may have broken. It is recommended to replace all 4 tub dampening straps at the same time. This part is sold individually.

Easy Part #:
EAP271100
Availability:
In Stock
Price:
$8.95

Round style oven igniter (igniter burner bake)

The round style oven igniter ignites the gas to light the oven burner to produce heat for your range. The igniter measures approximately 3 1/2” in length and the amperage range is 2.5 to 3.0. If the element has shorted out, no longer glowing, or glowing but only orange or red when it needs to be white, you will need to replace the oven igniter. When replacing the igniter please be very careful not to touch the gray element part of the igniter as it is very fragile. This igniter can replace igniters for either the broil or bake burners; it does not replace the flat-style igniters. The igniter includes two high-temperature wire connectors. This is a genuine OEM part. Please make sure to disconnect the power and shut off the gas supply before starting your repair.

Easy Part #:
EAP243425
Availability:
In Stock
Price:
$92.32

Dryer cycling thermostat (cycling thermostat (limit: 155-25))

The cycling thermostat with an internal bias heater will continually cycle the heating element off and on to maintain a constant inner temperature in the dryer. This cycling thermostat has a limit of 155 degrees Fahrenheit and a differential of 25 degrees. Meaning that the heating element will cut out at 155 degrees and cycle back on once the internal temperature drops by 25 degrees. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting the repair.

Easy Part #:
EAP11741405
Availability:
In Stock
Price:
$23.85

M series new style coil kit (coil-valve)

This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If there is no heat or your drying time is getting longer, the coils may be bad and will need to be replaced. Once the coils go bad they do not hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:
EAP334310
Availability:
In Stock
Price:
$26.40

Agitator repair kit (use wpl 285746)

This agitator repair kit is used to move the upper agitator and connects the base of the agitator with the agitator top mover. The kit is most commonly used if the top part of the agitator is not moving correctly but the bottom portion is. If your washer will not agitate or is noisy, you may need to replace the kit. The kit includes a medium cam, agitator dogs, bearing, thrust bearing washer, and a dust cap seal. Agitator grease is recommended for the repair, but it is not included with the agitator repair kit, it must be ordered separately. This is a genuine OEM part. Please remember to disconnect the power and water supply to the washer before starting your repair.

Easy Part #:
EAP334650
Availability:
In Stock
Price:
$23.00

Rear drum support roller kit (use wpl 349241t)

This drum support roller kit is used for square-ported model clothes dryers. It has a metallic bearing in its center. This support roller is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble, or takes too long to dry you might need to replace the roller. The kit is a genuine OEM kit and it includes two drum support rollers, four tri rings, and one retaining washer. It is recommended that you replace both rollers at once. Please remember to disconnect the power to your appliance before starting your repair.

Easy Part #:
EAP347627
Availability:
In Stock
Price:
$13.37

D-shaped knob clip (u clip)

This control knob clip helps secure the timer knob to the shaft allowing you to select the desired setting for your dryer. If the knob has become loose or the clip is missing you will need to replace the clip. This clip is a genuine OEM part, made of metal and is sold individually.

Easy Part #:
EAP268493
Availability:
No Longer Available

Rear drum bearing kit (rear bearing kit)

This rear drum bearing kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws. The support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. Over time the drum bearing will wear out. This kit will help keep your dryer running as smoothly as possible with as little noise as possible. This is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Easy Part #:
EAP459829
Availability:
In Stock
Price:
$52.07

Front glide kit

The front glide helps the drum rotate smoothly and quietly while operating. If your dryer will not tumble or is noisy, the glide could be worn down, causing a metal on metal noise, and will need to be replaced. It is recommended to replace both glides at the same time; a rivet tool is required for this installation. This kit includes a blue plastic glide, a brown cork pad, and two metallic rivets. The front drum glide kit is a genuine OEM part. Please remember to disconnect the power to the dryer before starting your repair.

Easy Part #:
EAP1804752
Availability:
In Stock
Price:
$13.68

Pan slide track (track)

This pan slide track can be used for either the left or right side of the pan.

Easy Part #:
EAP11739794
Availability:
In Stock
Price:
$21.56

Flat style oven igniter kit (igniter glowbar)

The flat style oven igniter is used to ignite the gas to light the oven burner in your range. If your oven is not heating, check the igniter to make sure it is glowing. If the igniter is glowing and your oven is not heating, then your igniter is not strong enough to heat the oven and you will need to replace it. When replacing the igniter please be very careful not to touch the black element part of the igniter as it is very fragile. The part measures approximately 3-3/4" in length and the amperage range is 3.3 to 3.6. The kit comes with a mounting bracket and a wire connector with a plug. *Please note: the connector plug might need to be removed and spliced to the range wiring using porcelain wire nuts. This is a genuine OEM part.

Easy Part #:
EAP231280
Availability:
In Stock
Price:
$48.22